How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
They are making a few good observations related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this great article on the next paragraphs.
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably difficult job. If the old tub is readily easily accessible, the task can move rapidly; if you need to open a wall surface to eliminate the old bathtub and place the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. See to it you have certified yourself for the job as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your shower room if you have actually currently acquired a brand-new bathtub and do not need to alter the plan of your previous water pipes.
Your tools as well as product list should make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome because of the limited gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer supplied backnut. When the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub up until the level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water system and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill up the bath tub and additionally check the overflow outlet and also the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it into its last placement.
Preparing for the Setup
To start with, the supporting frame provided with the bathroom should be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in difficulties with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are sold in tubes and also cartridges, as well as are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very involved in How to Install a Bathtub Yourself and I hope you enjoyed reading the new blog posting. For those who enjoyed our post if you please do not forget to pass it around. I enjoy reading our article about How to Install a Bathtub Yourself.
Book A Service Call
Report this page